ISE W288 ECO Motor Controller/ Frequency Converter Module
Hi,
In March 2018 I had an issue with my ISE W288 when it stopped mid cycle. I managed to track the problem down to a blown resister and chip on the controller board. Because my soldering skills were not up to scratch i ended up buying a new controller. Everything was working fine until a week ago when I heard a loud pop and the machine stopped mid cycle again. This time I traced the problem to the motor Frequency Converter Module. A small surface mounted capacitor has blown and taken out a number of other small components at the same time. My question is could there be something else wrong with my washing machine that is causing components to blow or am i worrying too much. As you can understand I am reluctant to install the new module that I have purchased if it is going to blow again.
Solution Summary
AI-generated from this discussion
This thread was marked as solved. Here's a summary of the problem and the fix, generated from the discussion below.
ISE W288 ECO stopped mid-cycle; repeated PCB/module component failures
- The problem
- An ISE W288 ECO washing machine stopped mid-cycle. The original poster had previously found a blown resistor and chip on the controller board in 2018 and replaced that controller. About a year later the machine stopped mid-cycle again with a loud pop, and the motor frequency converter module was found damaged, with a blown surface-mounted capacitor and other failed components. The poster was concerned that another fault in the machine might be causing repeated electronic board failures.
- Likely cause
- The discussion says a faulty motor could potentially damage a PCB/module, but this was not confirmed. Another suggestion was possible mains power surges. The accepted reply indicates the motor should ideally be checked with an insulation test meter. The exact cause of the repeated failures was not confirmed.
- What fixed it
- Recommended action was to have the motor tested, ideally with an insulation test meter, to rule out a motor fault before fitting further parts. A surge protector adapter was also suggested for future protection. No confirmed repair to the appliance was documented.
- Checks to try
- Failed components identified on the controller board in 2018
- Motor frequency converter module inspected after loud pop
- Main chip under the heat sink found blown
- Suggestion to test the motor with an insulation test meter
- Parts or tools mentioned
- Controller board
- Motor frequency converter module
- Insulation test meter
- Surge protector adapter
Safety: Further diagnosis should be carried out by a suitably qualified appliance engineer.
4 Answers
It's definitely possible for something like a faulty motor to blow something in a pcb. Ideally it should be checked with an insulation test meter but they are specialist expensive meter only carried by repair engineers.
Need Professional Help or Spare Parts?
Hi, Thanks for the reply.
I discovered that It was the main chip hidden under a heat sink that had blown and taken out the other components on the reverse side of the board.
Is it possible for a faulty motor to be responsible for damaging two separate modules over a year apart? Is this something you have encountered before.
If so I can get the motor tested, luckily on the estate where I work there is a company that deals with electric motors.
Best get it tested if that’s an option. However, as I expect you suspect yourself if a motor had a fault that would damage PCB components it seems highly unlikely it would behave for any length of time before doing it again. It’s possible both incidents have separate causes or even both incidents were not caused by other parts. Potentially power surges in the mains could be an issue although you’d hope the PCB would be protected by an appropriate fuse.
I would definitely consider using a surge protector adapter to project the appliance in future.
Need Professional Help or Spare Parts?
Sound like a sensible idea, I will get a surge protector. So far the machine has been behaving and I am hoping I have just had a run of bad luck...Fingers crossed....Thanks for the help.
Your Answer
Sign in to share your expertise and post an answer.
Related Questions
Disconnecting washing machine
0 answers • 2 replies
Power button not turning on washing machine
0 answers • 2 replies
Can this washer be repaired?
1 answer • 1 reply
Hotpoint F7 E2 Fault
1 answer • 1 reply
My Bosch washing machine is stuck on 33 minutes remaining
1 answer • 1 reply
Bosch washing machine door lock accidentally triggered with the door open – how I reset it
0 answers • 2 replies
Cant identify the correct replacement carbon brushea
0 answers • 2 replies
LG washing machine making intermittent noise — video link included
1 answer • 4 replies
Washing machine beeps then shuts down
1 answer • 1 reply
Candy washing machine below slip
1 answer • 1 reply