Trips in hot cycle, but heat element tests ok?
Bosch washing machine started tripping circuit breaker during normal hot wash. It drains ok, spins ok, does a cold wash ok, but part way into a hot cycle it trips trip switch and water never heats up, so I assumed it was a dodgy heating element.
I opened it up, removed heating element and multimeter reads 26 ohms across its live/neutral pins. My calculation is (220 x 220v) / 2000W = 24.2 ohms, so it's pretty close. No continuity between live/neutral and earth. Thermostat/temp probe is reading around 5 ohms, with multimeter dial at 20k, and falls with rising temp if I warm it up, so seems to be working too.
If it's not the heating element or temp. sensor what else could it be?
Thanks in advance!
Solution Summary
AI-generated from this discussion
This thread was marked as solved. Here's a summary of the problem and the fix, generated from the discussion below.
Bosch WFL2060GB trips electrics during hot wash; heater insulation fault suspected
- The problem
- Bosch WFL2060GB trips the circuit breaker part way through a hot wash and the water does not heat. The machine drains and spins when those functions are selected manually. The original checks showed the heating element measured about 26 ohms across its terminals, with no continuity from live/neutral to earth on a standard multimeter. The temperature sensor reading changed with warming, suggesting it responded.
- Likely cause
- The strongest supported diagnosis was a low-insulation leak to earth, most likely from the heating element. The forum explained that this type of fault may not show on a normal continuity meter and typically needs an insulation test meter to confirm. A second fault could not be ruled out because the machine also failed to complete a cold wash cycle normally.
- What fixed it
- Recommended action was either to have the appliance properly tested with an insulation tester by an engineer, or to gamble on replacing the heating element as the most likely cause. Reset procedures were not considered relevant, and no reset was confirmed for this fault.
- Checks to try
- Heating element measured approximately 26 ohms across live/neutral
- No continuity found between heating element terminals and earth using a standard multimeter
- Temperature sensor resistance changed when warmed
- Machine drained and spun when manually set
- Hot wash cycle tripped the electrics part way through
- Cold wash cycle did not complete normally
- Parts or tools mentioned
- multimeter
- insulation test meter
- heating element
Safety: Further diagnosis should be carried out by a suitably qualified appliance engineer.
5 Answers
Hello Alan. Unfortunately if you don't have an insulation test meter you can't troubleshoot a fusing or tripping electrics fault. A continuity test meter would detect a direct short to earth. But an appliance can trip with modern fuseboards with a relativley small leakage to earth that wouldn't be picked up with a continuity meter. The insulation test meter used by repair engineers puts 500 volts (DC) through the part to test for insulation leaks. It's explained in my article here - Washing Machine Tripping or Fusing Electrics
Need Professional Help or Spare Parts?
Thanks Andy - so given the facts (it drains ok, spins ok, does a cold wash + spin cycle ok, but part way into a hot cycle it trips tripswitch and water never heats up), is it reasonable to assume the problem is likely to be the heating element? Seems the most logical, and a simple enough replacement to try, right?
The heating element is one of the most common causes of tripping the electrics. Especially if it only trips part way through the wash cycle. You can't be sure, but if forced to guess it's the most likely explanation.
Need Professional Help or Spare Parts?
One more update - I had incomplete info yesterday. More details:
The machine does not finish a cold wash cycle, but ends without completing the spin/drain, and the lights indicate cycle has ended (no blinking/error). You can then manually set a spin cycle, which runs & drains ok, but it does not complete during the normal cold wash cycle. And the hot wash cycle is the one that trips the electrics.
What would that suggest - a dodgy circuit board? As well as a dodgy heating element? Seems like two different faults going on...
Is there a "master reset" for the Bosch WFL2060GB? I found one on-line, but it includes press/hold the spin button, but i don't have a spin button, just a spin dial! Maybe they meant Rinse Plus button? Another said to open/close door quickly 6 times, didn't seem to do anything (or else some-one's having a laugh!!).
There shouldn't normally be a need to reset anything. Once the fault is cleared it should work as normal. Aye the open and shut the door 6 times sounds very much like a wind-up
Low insulation faults can cause strange faults and behaviour on some washing machines. However, it's not possible to rule out more than one fault. If it doesn't complete the cold cycle I would assume it at least drains the water away even if it doesn't spin. The only thing you can do is get an engineer or gamble fitting a heating element.
Need Professional Help or Spare Parts?
Your Answer
Sign in to share your expertise and post an answer.
Related Questions
Hotpoint BI WMHG 81484 UK
1 answer • 2 replies
Hotpoint WMFUG942 Door Issue
1 answer • 1 reply
heater element issue
1 answer • 4 replies
Knocking sound in vintage Hotpoint First Editions 1000 - suggestions please!
1 answer • 3 replies
hotpoint wmxtf 842 - Door Interlock screws
1 answer • 1 reply
Hotpoint WM51 motor armature query
1 answer • 3 replies
Hotpoint selling split tubs again?
1 answer • 7 replies
Hotpoint WD21 "Starter Edition" question
1 answer • 5 replies
Samsung ecobubble keeps blowing the heating element.
1 answer • 26 replies
Hotpoint rd966j screen not working
1 answer • 3 replies