BOSCH WVG30461GB WASHER/DRYER NOT DRYING
Hi. We have a problem with our Bosch Washer / Dryer which keeps tripping and not drying. I reset the thermostat, but it does it again after a couple of washes. In the link below, someone had the same problem back in 2017, but he cleaned the Fan out of fluff. I would like to try the same, but it doesn't give a step by step guide, nor shows any pictures of what to take apart. Can anyone help?
Solution Summary
AI-generated from this discussion
This thread was marked as solved. Here's a summary of the problem and the fix, generated from the discussion below.
Bosch WVG30461GB washer/dryer drying thermostat trips repeatedly
- The problem
- Bosch WVG30461GB washes normally but the drying side stops because the dryer thermostat/TOC trips. Resetting it only restores operation temporarily and the fault returns after a couple of washes.
- Likely cause
- The discussion most strongly supports overheating in the drying system rather than overloading. Suggested causes were the fan not running, the fan or air path being blocked with fluff, or a blockage in the drying system or condenser chamber. Overloading was considered possible initially, but the fault continued even with the wash load reduced by half.
- What fixed it
- Recommended action was to check whether the fan runs on the dry cycle and whether water is trickling into the condenser chamber and being pumped away during drying. If these are normal, blockages in the drying/condenser system remain likely. It was also noted that the heating chambers usually need resealing with special heat-resistant sealant if opened. The exact repair was not confirmed in the thread.
- Checks to try
- Engineer previously reduced load size advice was tried, but the thermostat still tripped with half loads
- Engineer previously cleaned the thermostat area and heating elements, but the fault remained
- Check whether the fan is running on the dry cycle
- Check whether water is trickling into the condenser chamber at the back
- Listen for water being regularly pumped away during the drying cycle
- Parts or tools mentioned
- special heat-resistant sealant
Safety: Further diagnosis should be carried out by a suitably qualified appliance engineer.
8 Answers
Hi: Do you mean tripping the electrics or tripping a TOC?
Need Professional Help or Spare Parts?
Hi Andy. Just the Thermostat. It still washes but won't dry.
I'm quite handy with tools, but I don't like attempting something without a little instruction!
I should also add that I've had an Engineer out twice, he advised that we are overloading the machine the first time he came out, so we decreased the amount of washing by half and it still continued to trip. He came out a second time and cleaned the thermo and the elements but it's still doing it. My wife has never run the drum clean cycle in the three years we've had the machine, so i'm guessing we have the same problem as the original poster.
If the stat or TOC on the dryer is tripping out it's unusual for it to reset. They normally make them one shot only devices these days. That's because if it has a manual reset and someone keeps resetting it without fixing the fault it is not a good idea because it should only trip if it dangerously overheats.
Technically it's possible for bad overloading to cause it but if it still does it with half loads it has to be overheating due to the fan not running, or being blocked or a blockage somewhere in the drying system or condenser chamber. This article hear troubleshoots a similar fault where the TOC doesn't trip but the dryer doesn't dry properly because of a problem with condensing washer dryer hot & steamy
Need Professional Help or Spare Parts?
Thanks Andy. Do you therefore think then that it could be the same problem as the one in the link I attached, and therefore try and locate and clean the fan? If so, is it the long silver metal tunnel in the picture that needs to be removed to get to the fan?
If the fan is running on dry cycle and you can see that water is trickling into the condenser chamber at the back then blockages are distinct possibilities. These heating chambers usually need resealing with special heat resistant sealant though. Check that water is running into the condenser chamber at the back into the drum to be pumped away. One easy way to do that is to listed out for water regularly being pumped away down the drain during the drying cycle.
Need Professional Help or Spare Parts?
Thanks Andy, I'll give that a look.
Your Answer
Sign in to share your expertise and post an answer.
Related Questions
Hotpoint tumble dryer not heating but drum still turns
1 answer • 1 reply
Zanussi tumble dryer tripping the electrics every time
1 answer • 1 reply
Baumatic BDI1485D4E integrated washer dryer not drying.
1 answer • 1 reply
Bekon wdir7543101 washer dryer door won't open
1 answer • 1 reply
Hotpoint Washer Dryer NDD 9636 DA UK venting steam
1 answer • 2 replies
LG F4J6TMW0WW Washer Dryer - DE1 Error, now won't power on at all
1 answer • 3 replies
AEG 9000 SensiDry® 10 kg Washer Dryer Model No: L9WEC169R loud noise when drying
1 answer • 2 replies
Samsung combi dryer/washer motor ( EC2) code.
1 answer • 1 reply
Hisense Washer Dryer clicking noise
1 answer • 4 replies
blomberg lrf285411w washer dryer truning ON but no door lock detected
1 answer • 3 replies