Solved
Hoover

Hoover dryer not working

HEhelenm117
Asked over 4 years ago 4,952 views
0

Hi

please can someone advise, my hoover dryer as suddenly stopped working, I will pop it on and it will run for about 5 minutes then stop and 2 symbols will appear. I am not too sure what they mean?

I will attach a photo - it’s the 2 logos on the far right

Solution Summary

AI-generated from this discussion

This thread was marked as solved. Here's a summary of the problem and the fix, generated from the discussion below.

Hoover condenser dryer stops after 5 minutes with water tank and filter symbols lit

The problem
The Hoover tumble dryer runs for about 5 minutes, then stops and shows the two far-right symbols. From the discussion these were identified as the water tank warning and the lint/filter airflow warning.
Likely cause
The strongest diagnosis was significant internal lint build-up affecting both airflow and the condensate sensing system. Wet lint on the water sensor can make the dryer think the tank is full when it is empty, and lint on filters/condenser can reduce airflow and cause the filter warning.
What fixed it
Recommended action was to clean the dryer thoroughly, including the door mesh filter, condenser cassette and any other filters. A deeper internal clean was also advised because the symptoms together were said to commonly indicate heavy internal lint accumulation. The exact repair carried out was not confirmed in the thread.
Checks to try
  • Dryer runs for about 5 minutes then stops
  • Two warning symbols identified as water tank and lint/filter indicators
  • Water tank warning may appear even when tank is empty
  • Airflow through the filter system was reported as low
  • Suggested cleaning of the condenser cassette
Parts or tools mentioned
  • door mesh filter
  • condenser cassette
  • water tank sensor
  • compressed air

Safety: Further diagnosis should be carried out by a suitably qualified appliance engineer.

Cause identifiedGenerated 6 Aug 2026 · AI summaries can make mistakes — read the full thread below.
Was this summary helpful?

2 Answers

Accepted Answer
0
WH
WhitegoodshelpVerified Engineer
Answered over 4 years ago

Hi. The top one looks like a water symbol. Is it taking in water? Or is it filling with water but the water is running down the drain and not filling the drum?

A washing machine will abort the cycle and display error codes if it hasn’t filled with the right amount of water within a set period of time.

Any error symbols should be listed in the instruction manual although not all will have proper explanations

Download washing machine user manuals

Whitegoods Help — appliance repair expert and forum host.
0
KD
KDSmith
Answered over 4 years ago

The upper symbol relates to the water tank on this condenser dryer, it indicates the tank (erroneously?) needs to be emptied even when it’s actually empty

The lower symbol relates to the lint filter, the machine is indicating the the air flow through the filter is low and the filters needs cleaning, note this is the door mesh filter, the cassette and any other filter in the dryer

With other brands of condenser dryer I’ve worked on these two symptoms together with a short run and stop mean that there is a significant lint buildup inside the machine, typically the dryer will not have been cleaned internally of lint in more than a couple of years especially if it’s had heavy use

In the case of the water tank system, wet lint builds up on the metal prongs of the water sensor in a sump and the dryer thinks it is full of water even when it’s actually empty

In the case of the filter system, wet lint clings to the metal surfaces of the condenser and reduces drying efficiency and airflow

I’d recommend a through clean inside the machine, wet lint prevents the dryer working properly (dry lint is a fire hazard), you’ll need to take the covers off the dryer, ideally use compressed air outside the house

Short term you can try using a shower to clean the condenser cassette

Hope this helps

Your Answer

Sign in to share your expertise and post an answer.

NAC Repair

Need an engineer?

NAC Repair

Rather leave it to a pro? Book a fully qualified engineer to diagnose and repair your Hoover.

  • Vetted, fully qualified engineers
  • Nationwide UK coverage
  • Fast, fixed-price appointments
Spares4Appliances

Need a spare part?

Spares4Appliances

Fix it yourself for less. Get genuine replacement parts for your Hoover delivered to your door.

  • Genuine, manufacturer-approved parts
  • Fast next-day UK delivery
  • Secure checkout & easy returns