Solved
LG
WM2016CW

LG WM2016CW Spent a lot in parts and still out of balance

HAHaliaeetus70
Asked over 9 years ago 7,342 views
0

Hi all, just want to say thanks in advance for your help!! I have a LG wm2016cw front load washer, it went out of balance big time and found out it was a broken spider arm, so I replace the spider arm and while I was at it I also bought and replaced all new shocks, springs and door boot. It still goes out of balance, have no idea why. It sits on anti-vibration rubber feet I bought.. Is that a bad idea??? Was thinking of taking them off, thought maybe that's the problem, also was thinking of getting 3/4 inch plywood to put under it floor is a little spongy?? I don't know what else I could replace in it. Thanks again for your time!!! Ron

Solution Summary

AI-generated from this discussion

This thread was marked as solved. Here's a summary of the problem and the fix, generated from the discussion below.

LG WM2016CW rocks and walks on spin after spider arm and suspension parts were replaced

The problem
LG WM2016CW front-loading washer was reported to go badly out of balance on spin. The owner had already replaced the broken spider arm, shock absorbers, springs and door boot, but the machine still rocked side to side, sometimes knocked, and would walk without anti-vibration feet. The washer is installed on a slightly spongy wooden floor.
Likely cause
The strongest diagnosis in the discussion is unbalanced or possibly under-loaded wash loads rather than another failed component. One reply also noted that a broken spider arm is a separate issue from a true out-of-balance condition.
What fixed it
Recommended action was to treat this as a loading/balance issue: review how the machine is loaded and consider that anti-vibration feet are generally acceptable but not usually needed. No further component replacement was confirmed, and the exact repair was not documented.
Checks to try
  • Observed the machine rocking side to side during spin
  • Noted occasional knocking during spin
  • Confirmed the machine would walk without anti-vibration feet
  • Checked levelling as closely as possible
  • Identified installation on a wooden floor
  • Pausing and restarting allowed clothes to realign
Parts or tools mentioned
  • Spider arm
  • Shock absorbers
  • Springs
  • Door boot
  • Anti-vibration feet
Cause identifiedGenerated 18 Aug 2026 · AI summaries can make mistakes — read the full thread below.
Was this summary helpful?

3 Answers

Accepted Answer
0
WH
WhitegoodshelpVerified Engineer
Answered over 9 years ago

Being out of balance is a separate issue to something like a broken spider arm. Out of balance is when the outer drum swings violently and hits the side of the casing or jumps up and thumps the lid. It's normally caused by unbalanced loads although a fault could cause it. Anti vibration feet should be OK although normally unnecessary. What exactly is it doing when it goes "out of balance"?

Whitegoods Help — appliance repair expert and forum host.
0
HA
Haliaeetus70
Answered over 9 years ago

Thanks for getting back to me!! When it goes out of balance the machine rocks from side to side pretty good and sometimes knocks, without the ant-vibration feet on it, it will walk. I've got it as close to level as I can. It sits on a wooden floor, I've heard its better on concrete but I don't have that option. What I usually do is pause the load, that stops the drum from spinning and start it again clothes get re-aligned. It just seems to me I shouldn't have this problem?? Its my first front load washer, so am I over analyzing this, do most front loaders do this?? Thanks again!

0
WH
WhitegoodshelpVerified Engineer
Answered over 9 years ago

It sounds like it could be a classic case of unbalanced load, possibly under-loading. Try these two articles

Washing machine jumps and bangs on spin

Loading a washing machine

Whitegoods Help — appliance repair expert and forum host.

Your Answer

Sign in to share your expertise and post an answer.