Washing Machine Very Noisy When Spinning Fast
I have a washing machine that's started to be very noisy when spinning fast. The fault comes on even with a fairly moderate load of 2 or 3 towels, though not when empty. The noise is a terrible banging and rattling and seems to be coming either from inside the drum or just underneath it. I have checked for all the possible causes refered to on the Forum including worn bearings and damaged concrete blocks but I cant see any problem.
There is no movement in the drum, or signs of rust from the bearings, or rumble or any other noise when I spin the drum by hand. I have almost completely dismantled the washing machine to try to find the cause. I have removed the drum and the concrete blocks and can find nothing wrong with them and they were bolted on tightly. I have also removed the front section of the outerdrum so that I can examine the inside but it all seems ok. I have also examined the springs and mountings but all seems ok. The washing machine is only just over a year old and is otherwise in perfect condition so I am reluctant to scrap it and would be grateful for any suggestions
Solution Summary
AI-generated from this discussion
This thread was marked as solved. Here's a summary of the problem and the fix, generated from the discussion below.
Washing machine bangs and rattles on fast spin only with laundry in
- The problem
- The washing machine became very noisy on high spin with a moderate load, producing heavy banging and rattling from around the drum area. It did not make the noise when empty. The owner reported no drum play, no rust or rumbling from the bearings when turning the drum by hand, and found the concrete blocks, springs and mountings apparently secure after extensive dismantling.
- Likely cause
- The strongest diagnosis in the discussion was an obstruction moving between the inner drum and outer tub, or dropping into the sump hose/pump area and returning when water enters. Other possible causes mentioned were a cracked drum spider, out-of-balance loads or suspension faults, but these were not confirmed.
- What fixed it
- Recommended action was to disconnect the appliance, tip it back and forth to listen for anything sliding inside, and inspect the sump hose and pump for trapped items such as coins or other metal objects. The exact repair was not confirmed in the thread.
- Checks to try
- Checked for bearing play and rust signs
- Turned drum by hand and found no rumbling or unusual noise
- Checked concrete blocks and found them tight
- Examined springs and mountings
- Removed drum and front section of the outer drum for inspection
- Suggested: tip machine back and forth to listen for a loose object
- Suggested: inspect the sump hose and pump for trapped objects
- Parts or tools mentioned
- Sump hose
- Pump
- Concrete blocks
- Springs and mountings
- Outer drum
- Inner drum
Safety: Disconnect the appliance before carrying out checks. Further diagnosis should be carried out by a suitably qualified appliance engineer.
1 Answer
It sounds like you've covered everything. Something trapped between the outer tub and inner drum can cause a lot of noise, which isn't present without any laundry in, but you should have found it when you removed the drum. However, try disconnecting the washing machine and tipping it back and forth to see if you can hear anything sliding around in the tub. I've known cases where something metal was inside the washing machine but when the water drains out it drops into the sump hose out of sight. As soon as water comes into the washing machine it floats back into the tub and causes the noise when spinning. Try taking the sump hose off (which is the black hose leading from the tub to the pump) and checking for stuff like money in the hose or pump.
With washing machines that are very noisy on spin, but only with washing inside, common causes are obstructions inside the tub, loose concrete weights, cracks in the drum spider and out of balanced loads (How do I avoid out of balanced loads in my washing machine?) or suspension faults (Worn or damaged drum bearings usually cause a rumbling noise).
( Related: Washing machine is noisy )
Need Professional Help or Spare Parts?
Your Answer
Sign in to share your expertise and post an answer.
Related Questions
Washing machine grinding sound before drum spins- is it definitely the bearings??
1 answer • 2 replies
HISENSE 5S Series Auto Dosing WF5S1245BW bangs loudly on high spin
1 answer • 9 replies
Hisense washing machine very noisy spin
1 answer • 2 replies
Miele Washing Machine (Spinning Noise)
1 answer • 4 replies
Miele W5740 time stops and cycle carries on and unusual noise on spin
1 answer • 17 replies
Indesit IWSC 61251 S ECO UK - strange noise when spinning
0 answers • 1 reply
New Hisense washing machine sometimes bangs on spins
1 answer • 30 replies
Indesit spins violently and bangs around on the floor
1 answer • 1 reply
LG washing machine making loud noise while spinning
1 answer • 1 reply
Ratting noise at very start of cycle, before drum spins
1 answer • 1 reply
