Constant nightmare with washing machine
Evening everyone,
Im new here so firstly let me say Thankyou in advance to you knowledgeable people as I’m completely stumped.
Can anyone help?
My Bosh washing machine regularly stops towards the middle to end of the cycle with an E35 error.
Now I believe it’s normally to do with excess or blocked water but it keeps reoccurring.
The only way I can stop the beeping and get the door open to restart everything is like this:
- Open front little door at the bottom. Drain off water through a little pipe.
Then open the valve and let water out.
I then have to tip the washing machine forward to drain more water (appears from underneath flooding my room) and then it finally works again when I switch it back on.
This then happens randomly again on another cycle but more and more often.
It’s been a nightmare since we bought it and we have had engineers out who have replaced parts, pump etc.
Our drains are clear. Been told to check them. No issues there.
I’m at a loss as to what could be causing this.
Anyone know or can help?
Thankyou.
Solution Summary
AI-generated from this discussion
This thread was marked as solved. Here's a summary of the problem and the fix, generated from the discussion below.
Bosch washing machine stops mid/late cycle with E35 and intermittent draining/flooding issue
- The problem
- A Bosch washing machine repeatedly stops towards the middle or end of the programme with error E35. To clear it, the user has to drain water via the small front drain hose and filter area, then tip the machine forward, after which more water comes out from underneath and the machine will restart. The fault recurs randomly and has become more frequent. Previous engineers had already replaced parts including the pump, and the household drains were reported clear.
- Likely cause
- The strongest supported diagnosis is an intermittent water detection or drainage-related fault. The accepted reply suggested either a blocked pressure system if little water remains in the drum, or slow/intermittent pumping if a lot of water is still inside. Another forum reply suggested E35 may indicate water in the machine base triggering a float switch, possibly due to a leak or related switch/wiring issue. The exact cause was not confirmed.
- What fixed it
- Recommended checks were to establish whether the machine still contains much water when the error appears, inspect the base area for water around the float switch, dry any water found, and then trace any recurring leak source. Suggested leak sources included the door seal, soap drawer, pumps, hoses, cracked plastics, or loose clamps. No single confirmed repair was recorded in the discussion.
- Checks to try
- Observed whether there was a lot of water left in the machine when E35 occurs
- Checked household drains and found no issue
- Inspect machine base for water around the polystyrene float
- Check associated float-switch wiring
- Dry out any water in the base and monitor if it returns
- Check likely leak points including door seal, soap drawer, pumps, hoses, cracked plastics and loose clamps
- Parts or tools mentioned
- pump
- polystyrene float
- microswitch
Safety: Further diagnosis should be carried out by a suitably qualified appliance engineer.
2 Answers
Sorry I missed this. Is it fixed? If there's not much water left in machine and it does this it can be a blocked pressure system. If it has a lot of water inside when the error occurs it could be failing to pump water fast enough. That can be caused by various things but if it's intermittent it can be very hard to fix.
washing machine not draining water
washing machine sticks stops mid-cycle
Need Professional Help or Spare Parts?
On the off chance you're still having problems, BTW you didn't mention which model Bosch washing machine or its age so I've made a few assumptions 🙂
1. E35 indicates (perhaps erroneously?) that a leak has been detected by the float switch in the floor of the washing machine
2. Empty the machine, power off and open the back to see if there is any water around the polystyrene float which is used to detect early signs of flooding in the base of the washer, or problems with wiring to the associated microswitch
3. If there is water, you can dry it out and check but if the water / fault returns, you'll need to find out where the water is coming from, bear in mind the water may run down hoses or wires on to the floor making it difficult to find
4, Prime suspects are: the rubber door seal, the soap drawer, the pump(s) and cracked / split plastics or hoses if the machine is approx 3+ year or older, if the machine is new check for loose clamps screws etc
5. Hint: Use a sheet of dry news paper in the bottom of the machine to find where water is dripping from, if you're really struggling do an empty wash with brightly coloured food safe colouring added so you can see where water is coming from
Hope this helps
Your Answer
Sign in to share your expertise and post an answer.
Related Questions
Disconnecting washing machine
0 answers • 2 replies
Power button not turning on washing machine
0 answers • 2 replies
Can this washer be repaired?
1 answer • 1 reply
Hotpoint F7 E2 Fault
1 answer • 1 reply
My Bosch washing machine is stuck on 33 minutes remaining
1 answer • 1 reply
Bosch washing machine door lock accidentally triggered with the door open – how I reset it
0 answers • 2 replies
Cant identify the correct replacement carbon brushea
0 answers • 2 replies
LG washing machine making intermittent noise — video link included
1 answer • 4 replies
Washing machine beeps then shuts down
1 answer • 1 reply
Candy washing machine below slip
1 answer • 1 reply