Solved

Filter Wont Budge

IAIan99
Asked over 15 years ago 7,957 views
0

HI

I have an Ariston washing machine and there is something stuck in the filter. Its a Margarita 2000. I have snapped the plastic handhold/ handle that you use to twist the filter out. Its really jammed in and I noe cant get enough grip on the filter in order to twist it out. Does anyone have any ideas on how to get this out, anyone else been daft enough to do this ,any tips?

Any help would be greatly appreciated

Ian

Solution Summary

AI-generated from this discussion

This thread was marked as solved. Here's a summary of the problem and the fix, generated from the discussion below.

Ariston Margarita 2000 filter jammed and handle snapped

The problem
On an Ariston Margarita 2000 washing machine, the pump filter would not turn and the plastic handle used to unscrew it snapped off, leaving the filter stuck in place.
Likely cause
The accepted reply said this type of jam is often caused by an obstruction entangled in the filter, preventing it from unscrewing. In this case, the original poster confirmed there was a blockage because they were able to move it before removing the filter.
What fixed it
The accepted advice was that if the filter is jammed by an obstruction, it may be necessary to remove the hose leading into the pump and retrieve the item from there. The original poster instead carefully chiselled out the centre of the broken filter cap, shifted the blockage, then unscrewed the remaining filter body. They then bought and fitted a replacement filter.
Checks to try
  • Filter would not budge and the handle snapped
  • Blockage was moved before the filter could be unscrewed
  • Replacement filter was obtained after removal
Parts or tools mentioned
  • Replacement filter

Safety: Further diagnosis should be carried out by a suitably qualified appliance engineer.

Confirmed fixedGenerated 13 Aug 2026 · AI summaries can make mistakes — read the full thread below.
Was this summary helpful?

4 Answers

Accepted Answer
0
WH
WhitegoodshelpVerified Engineer
Answered over 15 years ago

I've had cases where the filter appeared to be jammed and wouldn't come out. It proved to be an under wire from a bra or another obstruction that was entangled in it and prevented it turning to screw out. I had to remove the hose leading into the pump and retrieve the obstruction from there.

If the filter is broken you may be able to get one although it might not be easy to get spares for it. What is the actual model number?

Whitegoods Help — appliance repair expert and forum host.
0
IA
Ian99
Answered over 15 years ago

Thanks for your reply

I managed to carefully chisel out the center of the filter cap, move the blockage a 50p and then unscrew the rest of the filter. Phew a very annoying task. I bought a replacement filter online and it arrived the next day. So thanks for you help but managed to sort it.

0
SA
sara
Answered over 13 years ago

Hi,

I have a hoover HSDw 126 washer dryer and I am having trouble pushing the filter back in. Firstly, it was very hard to screw it out. I cleaned out the blockage (a square bit of fabric) and when I came to put it in it won't go back in, it feels really hard. Also, the cover bit has come off from the actual filter and went I put them back together, the cover turns but doesn't seem to have a firm grip on the filter to turn it as well.

Have I broken it or is it that something is stuck still inside? I can't see anything in there, however..

Thanks

Sara

0
WH
WhitegoodshelpVerified Engineer
Answered over 13 years ago

It's difficult to know without being able to see it Sara. If it's a screw fit it probably relies on a plate at the back squashing the rubber to make the filter stay in and be water-tight as you screw it so you need to make sure that's happening.

Whitegoods Help — appliance repair expert and forum host.

Your Answer

Sign in to share your expertise and post an answer.