Hotpoint Bwm 129 Bearing Replacement
Hi folks....I have a 2006 machine and the bearings are gone, I have taken off all the panels I can, but it looks as though it is going to be a bit more difficult than usual to get the drum out to replace the bearings.
Anyone done this or any tips that I should know.....I don`t want to make it more difficult for myself than it already looks....
Thanks in anticipation.
Solution Summary
AI-generated from this discussion
This thread was marked as solved. Here's a summary of the problem and the fix, generated from the discussion below.
Hotpoint BWM129 drum bearing replacement advice
- The problem
- A 2006 Hotpoint BWM129 washing machine had failed drum bearings. The owner had removed accessible panels but found the machine looked harder than usual to strip in order to remove the drum.
- Likely cause
- Confirmed bearing failure. The accepted reply suggests this model may use a drum spider with the bearings and bearing seal already fitted, which would make replacement easier than designs where bearings are recessed into the plastic outer tub. This was presented as a possibility rather than confirmed from an actual strip-down.
- What fixed it
- The accepted advice was that drum bearing replacement on modern washing machines is generally a major strip-down and not recommended as a DIY repair unless the person is experienced and prepared for a difficult job. Before buying parts, the owner was advised to make sure the old bearings could be removed. The strongest supported repair route mentioned was replacing the drum spider assembly if it indeed comes with bearings and seal pre-fitted. The exact repair carried out was not confirmed.
- Checks to try
- All accessible panels had already been removed
- Parts list check indicated bearings were available for the Hotpoint BWM129
- Parts list check suggested a drum spider may be available with bearings and bearing seal already fitted
- Parts or tools mentioned
- Drum spider assembly
- Bearings
- Bearing seal
- Digital camera or phone for reference photos
Safety: Further diagnosis should be carried out by a suitably qualified appliance engineer.
1 Answer
I don't really recommend diy drum bearing replacements unless someone is pretty diy experienced, or an engineer in another field and/or very determined and up for a challenge. In most washing machines it's a big job requiring a complete strip down. Most washing machines have only plastic outer tubs these days with bearings recessed in, and difficult or impossible to knock out without either special tools or without damaging something. With many modern washing machines you are supposed to buy either a new rear tub or even a complete full tub with the bearings already pressed in.
It's outrageous that you can no longer just knock out the old bearings and fit new ones on so many washing machines these days. The cost of new tubs is so high
Having said all that it appears drum bearings are available for the Hotpoint BWM129 but before buying I would make sure I'd got the old ones out ok first. Looking at the parts list search for Hotpoint BWM129 bearings it appears there is a drum spider which should have the bearings and bearing seal already fitted. If so that should make the job a lot easier. I'm not familiar with the insides of this model but if the drum bearings are fitted inside an alloy spider then the should be a lot easier to replace than when fitted inside the plastic outer tub as Hotpoint drum bearings have been for a long time previous.
If you do strip it down, take lots of photos on a digital camera or phone if good enough quality so you can always refer to how things looked before, and wiring etc.
Need Professional Help or Spare Parts?
Your Answer
Sign in to share your expertise and post an answer.
Related Questions
Hotpoint F7 E2 Fault
1 answer • 1 reply
My Bosch washing machine is stuck on 33 minutes remaining
1 answer • 1 reply
Bosch washing machine door lock accidentally triggered with the door open – how I reset it
0 answers • 2 replies
Cant identify the correct replacement carbon brushea
0 answers • 2 replies
LG washing machine making intermittent noise — video link included
1 answer • 4 replies
Washing machine beeps then shuts down
1 answer • 1 reply
Candy washing machine below slip
1 answer • 1 reply
No longer starts.
1 answer • 3 replies
Mould keeps building up in my washing machine tray
1 answer • 1 reply
AEG Loud Knocking on Spin
0 answers • 1 reply