Ariston Av1048C Not Advancing
My beloved Ariston AV1048CUK isn't working! It's quite an old machine but has proved reliable over the years so I'd like to repair it if I can.
The problem is that the timer sticks part way through the wash cycle. I'm pretty sure it's not the timer itself but the timer is waiting for a response from something else, which never comes.
On a wash cycle the machine fills to the correct level. It then heats the water, as I can feel the door getting warm. The machine then spins the drum correctly, as it would to to agitate the clothes.
It's at this point the timer stops; the machine just sits there agitating the clothes.
I'm thinking the water level sensor works OK and that the heating element is OK too. What else would cause the timer to stop at this point in the cycle?
Would a thermostat stuck in the 'on' position cause this problem without boiling the water? What other sensors are involved at this point in the cyle?
Any ideas?
Solution Summary
AI-generated from this discussion
This thread was marked as solved. Here's a summary of the problem and the fix, generated from the discussion below.
Ariston AV1048CUK timer not advancing during wash
- The problem
- An Ariston AV1048CUK was filling correctly and agitating, but the timer stopped part way through the wash cycle and the programme would not advance. The original assumption was that it was waiting for a heating or temperature-related signal.
- Likely cause
- The strongest diagnosis in the discussion is inadequate or failed heating from the element, possibly due to a broken heater or heavy limescale causing very slow heating. The accepted reply also noted a timer fault was possible, but less certain. The later observation that hotter incoming hot water briefly allowed the machine to run supported a heating-related fault rather than a water level issue.
- What fixed it
- No confirmed repair was documented. The accepted advice was to focus on the heating system rather than replace the timer, as replacing the timer could waste time and money if it was not the cause. The thread supports a diagnosis of poor heating performance, but the exact failed part was not confirmed.
- Checks to try
- Machine filled to the correct level
- Door/water felt warm on a 40C wash
- Drum agitated normally
- On a 90C wash the water did not boil
- Machine briefly worked after the household hot water temperature was increased
Safety: Further diagnosis should be carried out by a suitably qualified appliance engineer.
4 Answers
Old washing machines behave differently as they don't have error codes. If it's heating the water then it's waiting for the thermostat to close having reached the correct temperature before moving on. If the thermostat doesn't close it should overheat (more modern washing machines will usually abort and indicate an error code). Therefore it's a strange fault. If it definitely is heating the water it's possible limescale or a broken heater could be making the process so slow it's appearing to get stuck. Can you hear the water heating up like in a kettle? If so, but the water isn't that hot it could be the heater broken or heavily caked in limescale.
Alternatively it's possible the timer is faulty and just not reacting to the thermostat closing. I would definitely not attempt to replace the timer because it may well not be that and that would be a lot of time and money wasted.
Need Professional Help or Spare Parts?
Well, on a 40C wash, if you open the door you can feel that the water is warm.
On a 90C wash the water certainly doesn't boil so something is presumably limiting the temperature...
Is there perhaps a secondary 'safety' thermostat in series with the heater which stops the thing overheating if the primary thermostat fails?
PS: I have no plans to replace the timer if it has failed - far to scary a prospect!
Hello Dave: No there's not usually a secondary cutout, which is why washing machines used to boil the water dry when the thermostat failed. If it's a hot and cold fill, could the water just be warm due to taking in hot and cold water?
Need Professional Help or Spare Parts?
I must admit I hadn't thought of that! D'Oh! Of course, the hot fill would make the water warm....
The wife managed to get the machine to work OK today, briefly, which caused some scratching of heads. How could it 'fix' itself before failing again?
Last night I switched the central heating boiler over to the winter setting, which increases the temperature of the hot water. What's the betting the incoming hot water is over 40C, which fools the machine into thinking the element is OK?
Your Answer
Sign in to share your expertise and post an answer.
Related Questions
Ariston Margherita A1635
1 answer • 1 reply
Ariston Aml125 - Lock Icon Flashing (And "9H", Too, If Time Set)
1 answer • 1 reply
Ariston Avl 145 Programs Wont Start.
1 answer • 1 reply
Ariston Avxl 140 Upper Two Lights Flashing
1 answer • 7 replies
Ariston 1400Swd Will Not Start (Anything)
1 answer • 1 reply
Ariston H2O Error Code.
1 answer • 4 replies
Power button not turning on washing machine
0 answers • 1 reply
Can this washer be repaired?
1 answer • 1 reply
Hotpoint F7 E2 Fault
1 answer • 1 reply
My Bosch washing machine is stuck on 33 minutes remaining
1 answer • 1 reply