Hoover dynamic
Hi my hoover dynamic washing Was displaying an E05 error code Which I believed was a temptrue sensor issue I ordered and fitted a new sensor Yeterday But after a few washes the error code is back ? Any help on this issue would be great full?
Solution Summary
AI-generated from this discussion
This thread was marked as solved. Here's a summary of the problem and the fix, generated from the discussion below.
Hoover Dynamic showing E05 after NTC sensor replacement
- The problem
- A Hoover Dynamic washing machine displayed E05. The owner believed it was a temperature sensor fault and fitted a new sensor, but the fault returned after a few washes. The machine stopped part way through programmes and showed E05, including on a 59-minute mixed cycle with 35 minutes left and on drain and spin with 5 minutes left.
- Likely cause
- The accepted advice was that E05 does not confirm the NTC alone and can indicate an NTC, heater or module-related fault, with wiring/connections also needing checking. Because the new sensor only appeared to help briefly, poor connections were considered a likely possibility. A main PCB fault was also mentioned as possible, but not confirmed.
- What fixed it
- Recommended action was to carefully check the wiring and connections related to the temperature sensing/heating circuit, and to test the heater for open circuit. The owner did not carry out the electrical tests and decided to get someone in to inspect it. The exact repair was not confirmed.
- Checks to try
- Observed that E05 returned after replacing the temperature sensor
- Noted the machine stopped mid-cycle on multiple programmes
- Advised to check wiring/connections
- Advised to test the heater for open circuit
- Parts or tools mentioned
- temperature sensor
- multimeter continuity test meter
Safety: Further diagnosis should be carried out by a suitably qualified appliance engineer.
9 Answers
Hello. Error codes implicating the temperature sensor (or NTC) often say things like, "NTC or module, check connections". The Hoover Nextra range uses, "NTC/Heater fault". So an error rarely implicates a specific part that is definitely the cause - which is a great shame. If it worked for a bit then failed I would very carefully check connections. There's always a possibility of a pcb fault, which I would advise against dealing with.
Need Professional Help or Spare Parts?
Hi thanks Andy for the reply by pcb you mean the actual circuit board may be the issue ? All programs on machine are working it just stops at some point during then and e05 code is displayed ?
Yes the main PCB, not the control panel. Exactly when does it produce the error? That may provide a clue. Put it on a 40 degree cottons wash and write down everything it does, and time everything up until the error.
For example when the error triggers what exactly was it doing? Was it 10 mins into a wash and turning the drum back and forth, or was it 40 mins in and draining the water away? Could you hear the water heating up?
Need Professional Help or Spare Parts?
Hi Andy thanks for your reply ( sorry for not replying sonner ) The machine is doing this on every selection we use Ie on the 59 mixed cycle it stops with 35 minutes left gos to error code On drain and spin which is 9 minutes long it stops with 5 minutes left same error
regards graham
Have you checked the heater for open circuit?
Need Professional Help or Spare Parts?
Hi can you explain what you mean by open circuit please ?
Regards
By open circuit I mean there is no reading when you test a component. So for example if you put one probe on each of a heating element’s connections the readings are the same as when both probes on the continuity test meter are not touching. In other words there is no circuit (open circuit).
Need Professional Help or Spare Parts?
Thanks for the reply I don not have eny testing equipment to do it with Will have to get some one in to take a look Thanks for all the help
regards graham
OK. You can buy a multimeter continuity test meter for just several pounds.
Need Professional Help or Spare Parts?
Your Answer
Sign in to share your expertise and post an answer.
Related Questions
Hoover H-Wash & Dry 350. HELP !
1 answer • 2 replies
Hi I have just wasted 2 hours trying to get help for a hoover washing machine
1 answer • 2 replies
Hoover Otsein Next 3650T/1-37 error E03
1 answer • 2 replies
Hoover Washer stopping 1-2 minutes into cycle
1 answer • 3 replies
Hoover counterweight replacement
1 answer • 2 replies
Hoover Vision VHD 9143 ZD
1 answer • 11 replies
hoover VTS714 D21 wont spin
1 answer • 5 replies
Hoover VT 814D21-80 not working
1 answer • 4 replies
Hoover Visiontech washing machine fault
1 answer • 4 replies
Hoover wdyn 9646pg-30s shut down after 15 sec
1 answer • 11 replies